Hand pumps to pump water by hand to furnish drinking water from wells and cisterns

Aermotor windmills pump water with wind power. Dean Bennett Supply has served the windmill customer since 1965. Call 800-621-4291 today to get help with your windmill, hand pump, pumping cylinder and other windmill system accessories.
HAND PUMPS for WATER WELLS			DEAN BENNETT SUPPLY Toll Free 1-800-621-4291 Smart Phone Dialable
Baker Monitor hand pumps have been the standard for the hand pumping industry. Many state camp grounds and forest service parks are using Baker hand pumps to furnish drinking water for visitors. With just a few strokes of the handle, water starts to come out the spout of the hand pump. That is because the well pumping cylinder in the well, holds the pipe full of water, allowing you easy access to the clean fresh drinking water, supplied from the Baker hand pump. MADE IN THE U S A BAKER / MONITOR FULL SIZE DEEP WELL HAND PUMPS Hand pumps allow you to pump water manually when the power goes out. A Cylinder in the well below makes water available to pump when there is no other source. Hand pump catalog page 59
$ 820.00	11HD		Force Hand Pump Stand with standard open spout	11HD Hand Pump
$ 1015.00	12HD		Force Hand Pump with bibb spout shut-off	1DFHCS
$ 1085.00	12HDA		Same as 12HD except tapped for 2" tubular well
$ 1970.00	1DFHCS		Fountain Pump Stand
			Baker's Fountain Pump Stand is available out of the factory on a special order basis. Please allow a few extra days for delivery. A few strokes of the handle fills a reservoir with water, which without further pumping, becomes a smooth flowing drinking fountain. Factory installed 100DPS shroud assembly is standard on Fountain Pump Stands.
$ 489.00	100DPS		Hand Pump Shroud Conversion Kit. Shroud kit replaces pump cap and flat bar on either 11HD or 12 HD force pumps to insure added sanitary protection.	100DPS Shroud Kit
$ 1125.00	11HDS		11HD Hand Pump with 100DPS Shroud Kit installed
$ 1340.00	12HDS		12HD Hand Pump with 100DPS Shroud Kit installed
$ 108.00	66MP		Sealed Pump Flange for 6" casing. Allows hand pump to be bolted directly on top of 6" steel casing.
$ 106.50	65MP		Sealed Pump Flange for 5" casing
$ 103.50	64MP		Sealed Pump Flange for 4" casing
$ 55.00	146HD		Hand pump spout to garden hose thread converter
$ 69.00	1HPS		Screen Kit for spout on above hand pumps

Baker Hand Pump Repair Parts

Baker's force pump stands ( deep well hand pumps ) are for use with windmills, pump jacks, or as a stand alone hand pump. They have a built in surge chamber, an adjustable stroke, and a multi-position cap. The #12-HD is identical to the #11-HD, except that it has a bibb spout in place of the standard open spout. The wheel handle valve in the bibb spout allows you to shut off flow to the spout, which allows water to be diverted thru an outlet plug on the back of the hand pump over to another point ( such as a storage cistern ).

Baker's Fountain Pump Stand is available out of the factory on a special order basis, so please allow extra time for delivery. A few strokes of the handle fills a reservoir with water which without further pumping becomes a smooth flowing drinking fountain. Factory installed #100DPS shroud assembly is standard on Fountain Pump Stands.

Sealed pump flanges allow your hand pump to be bolted directly onto your steel well casing.

Shroud kit replaces the standard pump cap and flat bar to insure added sanitary protection. It is recommended by many state and federal health / sanitary agencies.

Cistern pump like grandma had on her counter in the kitchen.

Fountain pump for a hand pump so you can get a drink from the fountain.

TABLE OF HAND PUMP DATA
Cylinder	5" Stroke	7-1/2" Stroke	10" Stroke
1-7/8"	221	154	119
2"	201	140	108
2-1/4"	167	117	90
2-1/2"	141	99	76
3"	104	72	56

Depth to water that can be pumped by an average person and showing the 3 depths possible with 5", 7-1/2", and 10" pin positions on the pump handle. Above calculations are based on 50 lbs applied perpendicular to the pump handle and includes the hydraulic lift with 10% added for the leather friction and weight of the rod at the minimum mechanical advantage which occurs at mid-stroke.

$ 215.00 #WP2 PLASTIC HAND LIFT PUMP with 4 x 3 Slip ABS Base Flange Pictured to the right on top
Made of rugged reinforced engineered thermoplastics with stainless steel plunger rod. Will not rust or corrode. Will lift water a maximum of 25 feet. Molded cup will not wear or deteriorate. Tapped for 2" pipe, which can be bushed down to smaller pipe.
$ 75.00 #HPP10 15" COUNTER TOP CISTERN PUMP Pictured to the right on bottom
Strictly for shallow well use, as it lifts by suction only. Pumps down to approximately 20'. Tapped for 1-1/4" pipe, has 3" cylinder size cup, and is heavy duty cast iron construction.

Typical Hand Pump System
( for a well 100' deep with a 50' static water level )

          $    820.00
          $    105.00
          $    158.76
          $    323.40
          $    159.00
          $      60.75
          $      13.95
          $ 1640.86

          $    199.00
          $    245.00
          $    120.54
          $    195.00

#11-HD Hand Pump
#66 MP 6" Sealed Flange
84' of 7/16" Galvanized Rod
84' of 1-1/4" Galvanized Pipe
2" All Brass Cylinder
5' of both rod and pipe for inside hand pump base
Cylinder Strainer
Total Cost of Basic System

Possible Add-on's
Pipe holder secures drop pipe while lowering or pulling galvanized pipe
Pipe Dog - Economical pipe lifting and setting tool
Each additional 21' of pipe and rod if your well is deeper
#12-HD with bibb spout in place of #11-HD additional cost.

Diagram of how a handpump pumps water.

Hand operated pump for transfer of fluids from a barrel.

PACER Hand Operated
Barrel Pumps
for Agricultural Chemicals
or Petroleum Transfer

FREIGHT IS PREPAID IF ORDER IS OVER $ 1,000.00

Hand Pump Helpful Hints:
click here for common questions about using a hand pump as a back-up water source.

HOME Emergency Hand Pump Pump Jacks Cylinders

Setting a Baker Hand Pump info

Setting the stroke on a hand pump cylinder

What if I bought a 11HD and now need a 12HD hand pump?

Prices effective March 1, 2013

How can I install a hand pump in my electric pump well?

Download our catalog in pdf format