WINDMILL
CYLINDERS

DEAN BENNETT SUPPLY
Toll Free   800 - 621 - 4291

# 449-B    ALL BRASS   OPEN TOP   WINDMILL CYLINDERS

Download 449B windmill cylinders page 61 in pdf

          $ 229.00 1-7/8" x 14" Stroke x 24" Overall Length    
for 2" Pipe   &  5/8" Rod		 pen top working barrel cylinders are used where you wish to pull the pumping plunger up from the cylinder to change leather cups without pulling all the pipe out of the well.
          $ 249.00 1-7/8" x 20" Stroke x 30" Overall Length    
for 2" Pipe   &  5/8" Rod
          $ 325.00 2-1/4" x 19" Stroke x 30" Overall Length    
for 2-1/2"     &  7/8" Rod
          $ 465.00 2-3/4" x 18" Stroke x 30" Overall Length     
for 3"Pipe    &  7/8" Rod
The #449-B  all brass open top style cylinder allows for both the plunger assembly and the bottom check to be pulled for service without pulling the steel drop pipe. All are constructed of 13 gauge seamless brass tubing, with all brass caps, a 3 leather ball valve brass plunger, and a ball valve brass bottom check.

# 442    ALL BRASS   FLUSH CAP   WINDMILL CYLINDERS

Download 442 windmill cylinders page 61 in pdf

   The flush cap all brass well pump cylinder is designed for shallower depths where pulling pipe from the well is not a big deal.
$ 159.00 2" x 10" Stroke x 18" Overall Length
for 1-1/4" Pipe   &   7/16" Rod
$ 183.00 2-1/4" x 10" Stroke x 18" Overall Length
for 1-1/4" Pipe   &   7/16" Rod
$ 199.00 2-1/2" x 10" Stroke x 18" Overall Length
for 1-1/4" Pipe   &   7/16" Rod
$ 269.00 3" x 10" Stroke x 18" Overall Length
for 1-1/4" Pipe   &   7/16" Rod
$ 295.00 3" x 12" Stroke x 20" Overall Length
for 2" Pipe   &   7/16" Rod
$ 485.00 4" x 13" Stroke x 20" Overall Length
for 2" Pipe   &   5/8" Rod
The #442 cylinder is all brass and is made from seamless brass tubing. Its flush cap design
(no outside caps) allows you to install a larger cylinder in a smaller diameter well.

#442 ALL-BRASS SLIM-LINE CYLINDERS TO ENTER 2" SCH 40 PIPE

Download 442 slim line windmill cylinders page 61a in pdf

The two sizes of #442 All-Brass "Slim-Line" Cylinders are designed for entry into 2" wells. Many driven wells have less than straight shafts, and therefore may possibly hinder placement of a well pumping cylinder for your windmill or hand pump. Also Old Pipe tends to corrode over time and can cause problems putting a cylinder pump down the well. We offer both sizes that will go into 2" Sch 40 pipe, however we recommend that if your shaft is crooked or has a lot of corrosion, that you choose the 1 11/16" cylinder, since the extra 1/8" may be the difference between a successful installation or a hang up.

$ 155.00 1 11/16" x  10" x  18"    #442 All Brass Cylinder tapped for 1" pipe and 7/16" rod, with a 10" stroke area.
$ 135.00
1 13/16" x  10" x  18"    #442 All Brass Cylinder tapped for 1" pipe and 7/16" rod, with a 10" stroke area.

A-40    CAST IRON   BRASS LINED   WINDMILL CYLINDERS

Download A40 cast iron windmill cylinders page 61 in pdf

$ 247.00

 2" x 10" Stroke x 16" Overall Length
for 1-1/4" Pipe   &   7/16" Rod		 The cast iron brass lined well pumping cylinder is tough as nails, so if you are wrench happy, it can take the extra stress.

$ 285.00

 2-1/4" x 10" Stroke x 16" Overall Length
for 1-1/4" Pipe   &   7/16" Rod

$ 280.00

 2-1/2" x 10" Stroke x 16" Overall Length
for 1-1/4" Pipe   &   7/16" Rod

$ 322.00

 3" x 10" Stroke x 16" Overall Length
for 1-1/4" Pipe   &   7/16" Rod
These cylinders have a heavy cast iron body, a brass inside liner, a 2 leather all brass plunger, all brass bottom check poppet, 7/16" galvanized plunger rod, and heavy outside cast iron caps that are tapped for 1-1/4" pipe.


DEEP WELL WINDMILL CYLINDERS

CYLINDER REPAIRS     HOME     HAND PUMPS      PUMP JACKS

Submersible Pump below a Windmill Cylinder

Price effective February 1, 2009 

Download our catalog in pdf format