WINDMILL ACCESSORIES |
DEAN BENNETT SUPPLY |
|
The AY McDonald Float Valve has a brass valve body that houses a rubber ball. The float arm is made of cast iron and is 19" long with a hole in the end for mounting a flat tank float. |
$ 35.75 |
1" #8713 AY McDonald float valve |
| The Midland All-Brass float valves have a brass body with a
precision machined seat for the guide to set into. A leather washer is on top of the
guide, secured by a lid that attaches to the handle arm. The design gives you a positive
shut off every time. By removing the two screws and connecting the handle in position
perpendicular to that shown, the valve can be used on the side of the watering trough,
instead of the bottom. |
 |
|
|||
| $ 37.25 | 3/4" All Brass Float Valve | $ 88.20 | 2" All Brass Float Valve |
| $ 49.75 | 1" All Brass Float Valve | $ 148.00 | 2-1/2" All Brass Float Valve |
| $ 60.35 | 1-1/4" All Brass Float Valve | $ 174.00 | 3" All Brass Float Valve |
| $ 72.30 | 1-1/2" All Brass Flaot Valve | $ 260.00 | 4" All Brass Float Valve |
|
|
|||
| $ 1.20 |
3/4" Replacement Leathers |
$ 3.05 | 2" Replacement Leathers |
| $ 1.30 |
1" Replacement Leathers |
$ 5.75 | 2-1/2" Replacement Leathers |
| $ 1.40 |
1-1/4" Replacement Leathers |
$ 7.90 | 3" Replacement Leathers |
| $ 1.75 |
1-1/2" Replacement Leathers |
$ 12.10 | 4" Replacement Leathers |
|
|
|||
|
|
|
HARD RUBBER FLAT STOCK TANK FLOAT |
MOLDED PLASTIC |
ALUMINUM FLAT |
$ 28.50 |
#8715 Flat hard rubber float is used with any of the above float valves to control the water level in your stock tank. Rubber float measures 2-3/4" thick and 12" diameter, with a 3/8" hole in the center for mounting to the float valve. The durability of hard rubber floats make them attractive for use where livestock are rough on the tank float. |
$ 27.95 |
#10PSTF 10" Diameter Molded Plastic Stock Tank Float with hole in middle for pigtail rod. |
$ 56.25 |
#12ASTF 12" Diameter Aluminum Flat Stock Tank Float that are welded aluminum with center hole for 15" pigtail rod to connect to your valve arm. 3-1/4" thick |
| $ 45.75 | #8ASTF 8" Diameter Aluminum Flat Stock Tank Float that are welded aluminum with center hole for 15" pigtail rod to connect to your valve arm. 3-1/4" thick |
|
|||
|
8-1/2" long Brass Pigtail Tie Rod for through the flat stock tank float is adjustable with the bronze clamp. This type pigtail can be used with any type of float valve, whether it has a short arm or an extended length arm. Makes for easy adjustment of water level. |
|||
| 8 1/2" Brass Pigtail Rod with Bronze Adjustment Clamp | $ 8.25 @ | ||
| 15" Brass Pigtail Tie
Rod for through thicker aluminum stock tank floats with Aluminum Adjustment Clamp. |
$ 16.50 @ | ||
|
|||
|
1/4" Brass Rod is 12 1/2" long with 1/4"-20 thread. Can be used on Robert Bob Floats to make use of the Reliable stock tank float easier. |
|||
| 12 1/2" Brass Rod 1/4"-20 threaded | $ 7.70 @ | ||
|
||
$ 36.50 |
R440-5 |
5" Round Copper Float Ball w/ 1/4" - 20 SAE Female Thread |
| $ 43.25 | R440-6 | 6" Round Copper Float Ball w/ 1/4" - 20 SAE Female Thread |
| $ 91.50 | R440-8 | 8" Round Copper Float Ball w/ 3/8" Female NPT Thread |
Rod Centralizers catalog page 66
How to install rod guides of
fiberglass pump rod.
| $ 12.45 | 5/8" x 2" Rod Guide | For use with 5/8" fiberglass sucker rod in 2" pipe. These guides act as centralizers for your rod, which helps prevent excessive rod wear and splintering. Manufacturer or rod recommends two guides per length of rod for optimum protection and long rod life. |
| $ 14.70 | 5/8" x 2-1/2" Rod Guide | For use with 5/8" fiberglass rod in 2-1/2" pipe |
$ 12.45 |
3/4" x 2" Rod Guide |
For use with 3/4" fiberglass rod in 2" pipe |
| $ 14.70 | 3/4" x 2-1/2" Rod Guide | For use with 3/4" fiberglass rod in 2-1/2" pipe |
| $ 21.80 | 3/4" x 3" Rod Guide | For use with 3/4" fiberglass rod in 3" pipe |
|
Installing
rod guides with the rod guide install tool.
|
| $ 13.95 |  |
1-1/4" x 8" STRAINER | Schedule 80 heavy wall PVC plastic
pipe - finely mill slotted with 10 slot ( 10/1000" wide ) openings. Has 1-1/4" male pipe thread to screw directly into the bottom of your cylinder. Length is 8" with a flush bottom plug. |
|
| $ 15.95 | 1-1/2" x 8" STRAINER | Schedule 80 PVC strainer with 1-1/2" male NPT. | ||
| $ 17.50 | 2" x 8" STRAINER | Schedule 80 PVC strainer with 2" male NPT. | ||
 |
Quick Disconnect #374 1/2 |
| $ 69.95 | The A-374-1/2 Quick Disconnect Pump Pole Adapter bolts on to your windmill's wood pump pole and has a spring loaded pin that will connect to either a hand pump or pump jack |
| $ N / A | FP-51 FLAT WINDMILL BAR is 1/2" thick x 1" wide x 42" long flat steel bar with 7/16" male rod thread on one end. Two 1/2" holes are drilled thru the bar to allow for easy attachment of windmills and pump jacks to the sucker rod. |
 |
$ 6.50 $ 17.50 |
Quart of Windmill Oil Gallon of Windmill Oil |
Only $ 5.35 each in full case of 12 quarts. Only $ 14.25 each in full case of 4 gallons. |
Prices effective November 9, 2011
